Metal containers configurator Estimated form completion time: 5 minutes Requested by (Agent) Email address of person completing the form CUSTOMER DETAILS Company name Company contact email Telephone/mobile phone VAT number Contact person name Shipping address finished product STANDARD CHOICES Container type Sheet metalMesh Quantity Quantity required Any quantity 2 Any quantity 3 Base dimensions a x b (mm) 800 x 6001000 x 8001200 x 8001200 x 10001500 x 8001500 x 1000Special Length long side A (mm) Length short side B (mm) Standard reference model Height c (mm) 4005006508001000 Ground clearance d (mm) StandardOther Specify ground clearance d (mm) Ground support With sledWith boxed foot Sled short sideSled long sideBoth sides Sheet metal/mesh hatch YES in sheet metalYES in meshNO Hatch short sideHatch long sideBoth sides Hatch short sideHatch long sideBoth sides Bottom properties Standard corrugatedSmoothReverseDouble welded bottom Side properties Standard corrugatedSmooth Colour Yellow RAL 1007Orange RAL 2004Blue RAL 5010Red RAL 3016Sky Blue RAL 5012Grey RAL 7001Green RAL 6011White RAL 9010Black RAL 9005Special RAL Enter desired RAL colour Desired capacity - Sheet metal containers 1200 kg1700 kg2200 kgOther - Special Specify the load capacity desired [kg] Desired capacity - Mesh containers 800 kg1000 kg1500 kgOther - Special Specify the load capacity desired [kg] Needs sheet/mesh cover YES in sheet metalYES in meshNO Specify Type Freestanding/Hinged with manual openingHinged with gas spring assisted opening Padlockable? YESNO Specify Type Freestanding/Hinged with manual openingHinged with gas spring assisted opening Padlockable? YESNO Additional precautions with respect to company standards for sharp edges (e.g. edge grinding/burr removal)? YESNO Specify CONTAINER USE Contents stored in the container Type of product Dimensions Material How the product is loaded/unloaded into/from the container ManuallyWith equipment Specify the equipment used Container handling within the plant With forkliftOther Dimensions of the arm/fork lifting the container Specify whether tipping forks are used YESNO Need to move the fully loaded container by applying force on the sides (e.g. pushing with forklift forks on the sides) YESNO Container intended for use within an automated warehouse YESNO Specify dimensional limits/conditions Particularly smooth/aesthetic surface finish required YESNO Specify expectations Need to increase standard stackability (1+3 containers) YESNO Specify Need to lift the containers using a crane YESNO Need to weld all edges watertight on the inside YESNO Need for watertight internal liquid holding tank YESNO Desired tank height (mm) Inner container lining with acid-resistant plastic material YESNO Specify the acids you intend to store Needs forklift slots under the bottom YESNO Dimensions of the fork slot section - BASE X HEIGHT Distance between fork slots The container is tilted sideways (0/ +- 90°) by means of the fork slots YESNO Needs liquid drainage holes in the bottom of the container YESNO Location Hole diameter (mm) Needs holes or openings in the sides of the container YESNO Hole diameter (mm) / Opening size (mm) Specify location On 1 long sideOn 1 short sideOn both long sidesOn both short sides Eliminate container rims? Note: the container will no longer be stackable YESNO SPECIAL CHOICES Lowered sides YESNO Height front long side (mm) Height rear long side (mm) Height right short side (mm) Height left short side (mm) Hopper side YESNO Front long sideRear long sideRight short sideLeft short side Support other than steel under the sled YESNO WoodHard plastic (e.g. PA6GF30)Soft rubber C4M marine paint cycle for corrosive environments YESNO Hot-dip galvanising of the container YESNO Needs overpainting? YESNO Colour Yellow RAL 1007Orange RAL 2004Blue RAL 5010Red RAL 3016Sky Blue RAL 5012Grey RAL 7001Green RAL 6011White RAL 9010Black RAL 9005Special RAL Enter desired RAL colour Other surface treatments YESNO Specify the treatment required Structural calculation technical report drawn up by a qualified registered engineer YESNO Are there special regulations that must be complied with? Specify Weight label required YESNO Sticker with measured valueSticker with customer-specified value Specify the position (always near the top of the side) Right short sideLeft short sideRight long sideLeft long side Needs painted text YESNO Specify text - Default font height 40 mm Enter text RAL colour Specify location On 1 long sideOn 1 short sideOn both long sidesOn both short sides Wording produced by cold stamping on steel sheet YESNO Specify text - Default font height 40 mm Specify location On 1 long sideOn 1 short sideOn both long sidesOn both short sides Needs painted logo YESNO SUPPLY LOGO in .PNG BLACK AND WHITE and .DWG/DXF OPTIMISED format - if not available provide logo image Specify location On 1 long sideOn 1 short sideOn both long sidesOn both short sides Needs internal separator YESNO Length (mm) Width (mm) Height (mm) Specify location Long side at centrelineShort side at centrelineOther location Specify Type FixedRemovable Sheet metal type SmoothCorrugated Needs painted sequential number YESNO Specify number sequence - Default font height 40 mm Enter text RAL colour Specify the position (always near the top of the side) Right short sideLeft short sideRight long sideLeft long side Needs metal card holder YESNO Mounting WeldedRivetedRemovable Format A4A5Other Specify required dimensions Specify location Right short sideLeft short sideRight long sideLeft long side SHIPPING Carriage freeCarriage forward Delivery request date NOTE Additional notes/requests/specifications
